**Title (unchanged):** How do I record vocals at home and make them sound professional? Professional-sounding home vocals come down to four things in this order: the room, the performance, the mic placement, and the chain. Notice that "expensive mic" isn't on that list. A $99 SM58 in a treated closet beats a $3,000 U87 in a tiled bathroom every single time. ### Step 1 — Fix the room first Your room is doing more to your vocal than any plugin will. Untreated rooms add ringing, flutter echo, and a boxy honk in the 200–500 Hz range that no EQ can fully remove. The cheap fix: record in a clothes-filled closet. Hang heavy blankets on three sides of the singer. Stand on a rug. Aim the mic at the clothes, not at a hard wall. This is genuinely how a lot of released vocals are tracked. The slightly-better fix: a portable vocal booth (sE Electronics Reflexion Filter) plus a packing blanket behind the singer. Total cost: under $250. ### Step 2 — Choose a mic that suits the voice - **Large-diaphragm condenser** (Audio-Technica AT2020, Rode NT1 5th gen, Aston Origin): the default for most pop, R&B, and singer-songwriter vocals. Detailed and airy. - **Dynamic mic** (Shure SM7B, Shure SM58, Electro-Voice RE20): forgiving of room noise, great for rap, rock, podcasting, and any voice that gets harsh on a condenser. Needs a strong preamp or a Cloudlifter / FetHead inline booster. - **Ribbon** (Royer R-10, sE Voodoo VR1): smooth, vintage, less common at home. If you're unsure, an SM7B + Cloudlifter is the safest universal pick. ### Step 3 — Get the placement right - 6–8 inches from the mic. - Pop filter 2 inches in front of the mic. - Mic at nose-to-mouth height, angled slightly down. - Singer slightly off-axis (5–10°) to soften sibilance and plosives. - Headphones over both ears, with one ear slightly slipped if pitch reference is hard. ### Step 4 — Set gain properly Peaks should hit −12 to −6 dBFS in the DAW. Never let it touch 0. 24-bit gives you so much headroom you don't need to push it. Hot signals at the source make every later step harder. ### Step 5 — The chain A workable home vocal chain, in order: 1. **High-pass filter** at 80–100 Hz to kill rumble. 2. **Subtractive EQ** — find and cut the boxy frequency (usually around 250–400 Hz, narrow Q). 3. **De-esser** before compression, targeting 5–8 kHz. 4. **Compression #1** — fast attack, medium release, 3:1, 3–5 dB gain reduction (FabFilter Pro-C2, Waves CLA-76, stock DAW comps all work). 5. **Compression #2** — slower attack, 2:1, 2–3 dB gain reduction. Two stages of gentle compression sounds more natural than one stage doing all the work. 6. **Additive EQ** — small boosts: 100–120 Hz (warmth), 3 kHz (presence), 10–12 kHz (air). 7. **Saturation** — a touch of tape or tube (Soundtoys Decapitator, FabFilter Saturn). Sparingly. 8. **Reverb + delay sends** — a short plate or room (0.8–1.4s) plus a 1/4 or 1/8 dotted delay. ### Common mistakes 1. Recording in a bathroom or kitchen "for the ambience." 2. Singing too close to the mic and creating proximity-effect mud. 3. Stacking 6 plugins to fix a bad take instead of doing another take. 4. Forgetting the pop filter. 5. Mixing the vocal with headphones cranked — the vocal will end up too quiet in the final mix. ### Pro tip Record at least three full takes and one quiet/intimate take. Comp the best lines. Then double the lead with a quiet, soft version panned center, blended at −12 to −15 dB. This is the trick behind 90% of "how is that vocal so present?" radio mixes. ### When to hire a pro If the song matters — paid release, sync placement, label submission — hire a vocal producer for the session and a mixing engineer for the mix. A great vocal producer will get a performance out of the singer that no amount of plugins can fake.

0 Answers· Recording· asked by anonymous· 5/10/2026

0votes